What this product reference covers.
Gasoline or petrol is a volatile blend for spark-ignition engines whose grade depends on octane, vapour-pressure, distillation, oxygenate and regulatory requirements.
Products within the family.
Names used in commerce can overlap. Use the nominated standard and exact grade rather than relying on a generic product label.
Regular gasoline
Regular gasoline is a recognised gasoline / petrol category whose exact composition, grade limits and suitability must be confirmed from the governing specification and equipment requirement.
Premium gasoline
Premium gasoline is a recognised gasoline / petrol category whose exact composition, grade limits and suitability must be confirmed from the governing specification and equipment requirement rather than inferred from the generic label.
Ethanol-blended petrol
Ethanol-blended petrol is a recognised gasoline / petrol category whose exact composition, grade limits and suitability must be confirmed from the governing specification and equipment requirement rather than inferred from the generic label.
Reformulated / low-emission gasoline
Reformulated / low-emission gasoline is a recognised gasoline / petrol category whose exact composition, grade limits and suitability must be confirmed from the governing specification and equipment requirement rather than inferred from the generic label.
What the product is built from.
| Component | Technical role |
|---|---|
| Hydrocarbon or renewable blendstocks | Set volatility, density, ignition, energy and cold-flow behaviour. |
| Performance additives | May support stability, detergency, lubricity, conductivity or low-temperature operation. |
| Oxygenate / biocomponent where specified | Changes combustion, water response, oxidation and material compatibility. |
| Unwanted water, sediment or cross-product material | Contaminants can alter safety, operability and specification results. |
Define the decision before selecting the panel.
- 01
Confirm new gasoline / petrol identity, grade and fitness for the intended application.
- 02
Detect contamination, degradation, mixing or storage-related change.
- 03
Investigate abnormal equipment, combustion, filtration or handling behaviour.
- 04
Establish a representative baseline for later comparison.
- 05
Support specification, maintenance and root-cause decisions with corroborated evidence.
What each result contributes.
“High” and “low” are directional investigation prompts, not pass/fail decisions. Corroborate them using the correct specification, baseline and companion evidence.
Open ASTM, ISO, IS/BIS, DIN and companion methods →| Test / parameter | Typical methods | Why it matters | Possible causes when high | Possible causes when low |
|---|---|---|---|---|
| Density / relative density | ASTM D4052 / ISO 12185 | Supports identity, blending, quantity conversion and energy-related calculations. | Heavier components, oxidation residue, contamination or the wrong grade. | Lighter blendstock, volatile contamination, dilution or a different grade. |
| Distillation / volatility | ASTM D86 / ISO 3405 or product-specific method | Describes boiling distribution, evaporation and compositional change. | Heavy-end contamination, residue, weathering or off-grade blending. | Light-end enrichment, solvent contamination or a lighter product. |
| Flash point | ASTM D93 / ISO 2719 or product-specific method | Screens volatile contamination and supports safe handling. | Loss of light ends, heavier composition or method difference. | Petrol, solvent or other volatile contamination; incorrect product. |
| Water and sediment | ASTM D6304 plus product-appropriate sediment methods | Identifies corrosion, filtration, combustion, microbial and storage risks. | Condensation, tank bottoms, delivery contamination, leakage or poor housekeeping. | Dry handling and separation; an unrepresentative sample can under-report. |
| Sulfur / composition markers | ASTM D5453 / D4294 / product specification | Supports grade identity, emissions and contamination assessment. | Wrong grade, cross-contamination or unsuitable blendstock. | Lower-sulfur material, dilution or a different approved formulation. |
| Research / motor octane number | ASTM D2699; ASTM D2700 | Measures resistance to knock under controlled spark-ignition engine conditions. | Higher-octane blend components or oxygenates; confirm volatility and specification at the same time. | Off-grade blending, low-octane contamination, weathering or incorrect product. |
| Vapour pressure | ASTM D5191; EN 13016 | Controls volatility relevant to starting, evaporative emissions, vapour lock and seasonal grade. | Excess light ends, butane-rich blending, wrong seasonal grade or volatile contamination. | Weathering, loss of light ends, heavy contamination or wrong seasonal grade. |
| Alcohol / oxygenate content | EN 1601; ASTM D4815 or validated chromatography | Confirms blend identity and supports water tolerance, material compatibility and volatility interpretation. | Over-blending, cross-contamination or wrong grade. | Under-blending, phase separation, dilution with hydrocarbon fuel or wrong product. |
| Copper corrosion | ASTM D130; ISO 2160 | Screens corrosivity toward copper-containing bearings, coolers, bushings and yellow-metal components. | Reactive sulfur, acidic degradation, contamination or formulation incompatibility; report uses a corrosion rating rather than concentration. | A low corrosion rating is favourable but does not rule out in-service copper wear. |
Condition-monitoring application.
Once the product is in service, the question changes from “does it meet a product requirement?” to “what has changed, why, how confident are we and what action is proportionate?”
- 01Use a stable, representative sampling point and document operating hours, top-ups, transfers and maintenance.
- 02Trend method-consistent results rather than treating one value as a complete diagnosis.
- 03Separate new-product conformance from in-service condition and machine-wear questions.
- 04Escalate correlated evidence and rate of change; confirm surprising results before major action.